IACSIT International Journal of Engineering and Technology Vol 5 No 3 June 2013406DOI 107763IJET2013V5585 a lower dynamic coupling between the connected buildings is determined On the oth ID: 523113 Download Pdf

Embed / Share - Abstract

Abstract—A representative case study of potential earthquake-induced pounding between adjacent R/C frame buildings with insufficient separation gaps is examined in this paper. The height of the two examined buildings is the same, but their response is affected by considerable torsional pounding effects. An upgraded version of the traditional linear viscoelastic model for the numerical time-history analysis of the dynamic impact problem is proposed and implemented in the finite element model of the buildings. The results of the assessment enquiries carried out in current conditions, and a damped interconnection-based mitigation solution based on the incorporation of pressurized fluid-viscous dissipaters across the inadequate separation gaps, are presented. Evaluations of the benefits provided by the retrofit intervention, and some of its technical installation details, are finally offered. Index Terms—Damped interconnection, impact models, mitigation strategies, seismic pounding. I. INTRODUCTION Earthquake-induced pounding between closely spaced buildings is one of the highest sources of seismic vulnerability, as it can cause severe damage to non-structural and structural members, and even contribute to structural collapse [1], [2]. Pounding impacts derive from the out-of-phase vibrational response of the colliding structures induced by their different dynamic characteristics, when their separation joints at rest are not wide enough to accommodate the maximum relative displacements. Insufficient separation between adjacent buildings is typical of old city centers, where masonry buildings are normally in full contact along the height, as well as of modern urban blocks, where buildings were designed without any seismic provisions or by referring to earlier editions of the current seismic Standards, and thus generally with inadequate separation. Prevention of pounding in new structures is easily attained by adopting properly sized gaps, although with some limitations for tall buildings, deriving from the loss of useful floor space and the technical set up of proportionally sized expansion joints. On the other hand, mitigation of pounding hazards in existing buildings is usually a very demanding issue. A traditional mitigation strategy is represented by a general Manuscript received February 13, 2013; revised May 22, 2013. This work was supported in part by the Italian Department of Civil Protection within the ReLUIS-DPC Project 2010/2013. S. Sorace is with the Department of Civil Engineering and Architecture, University of Udine, Via delle Scienze 208, 33100 Udine, Italy (e-mail: stefano.sorace@uniud.it). G. Terenzi is with the Department of Civil and Environmental Engineering, University of Florence, Via di Santa Marta 3, 50139 Florence, Italy (e-mail: terenzi@dicea.unifi.it). stiffening of the individual potentially colliding buildings, aimed at reducing their absolute and relative displacements. However, whatever the stiffening method chosen, this strategy represents the most expensive and invasive approach to the issue, as it involves a complete seismic retrofit of the structural systems. Alternative strategies are based on local interventions in the predictable contact areas. The first solution consists in rigidly linking the adjacent structures by means of coupling beams [3] or shock transmitters [4], the latter being preferred especially for buildings with a wide plan, as they provide stiff connections during earthquakes, while avoiding the rising of significant forces related to the thermal elongation effects. While this rigid interconnection-based approach, which is derived from similar mitigation solutions adopted for bridge structures, allows preventing collisions, it can generate considerable increases in seismic story shears, and thus in the stress states of the structural building members. Also, the dynamic response of the joined structures appreciably differs from the response in the original separated configuration, and sometimes it can cause unfavorable effects as compared even to the most demanding out-of-phase pounding response conditions. A careful numerical evaluation of the consequences of the interconnection interventions is required to identify the best linking layout. The second solution is represented by the introduction of “sacrificial” elements, also named “crash box interfaces” [4], e.g. crushable parapets and carters, or strong collision walls acting as bumpers [5], all capable of protecting the contact-prone structural members. In case of pounding, these elements are subject to remarkable damage and require post-earthquake repair (collision walls) or substitution (crushable devices), at rather high costs and with a interruption in the use of at least some portions of the buildings. This implicitly fails to meet the basic requirements imposed by the last generation of international seismic Standards for what concerns the Operational and Immediate Occupancy performance levels, in spite of the fact that structural and non-structural members may formally meet them, thanks to the protective action of the “sacrificial” elements. The third mitigation strategy refers to the concept of structural interconnection too, like for the rigid linking approach recalled above, but it is based on the installation of energy dissipating devices across the separation gaps, with the aim of substantially reducing the severity of collisions rather than preventing them [6]. The advantages are represented by the remarkably lower interaction forces transmitted as compared to the rigid link configurations, thanks to the dissipative action of the dampers. Furthermore, Damped Interconnection-Based Mitigation of Seismic Pounding between Adjacent R/C Buildings S. Sorace and G. Terenzi IACSIT International Journal of Engineering and Technology, Vol. 5, No. 3, June 2013406DOI: 10.7763/IJET.2013.V5.585 a lower dynamic coupling between the connected buildings is determined. On the other hand, like for any type of interconnection-based intervention, an agreement between the owners of the buildings is legally required, in consideration of the mutual alterations made (which can be rated, in terms of town planning rules, as a transformation of two originally separate units into a new whole unit). From a numerical modeling viewpoint, the incorporation of dampers accentuates the non-linear charproblem, which makes it solvable only by means of a time-history dynamic analysis aspects consist in determining the optimal damping properties of the devices, as well as their best layout in the collision zones. The remaining design variables are the same as for a rigid linking problem, i.e. related to the dimensions of the existing separation gaps, as well as to the geometric and material characteristics of the adjacent buildings (with equal height and aligned floors; with different height and aligned floors; with equal or different height, but not aligned floors; with any of these configurations, and significantly differing floor masses; or else, multiple buildings in a row; corner with buildings in orthogonal rows; buildings with an asymmetric structure, causing torsional pounding, etc). This paper offers a synthesis of a research study dedicated to the analysis of pounding between reinforced concrete (R/C) frame buildings and its mitigation by a damped interconnection strategy based on the incorporation of pressurized fluid viscous (FV) dampers as protective devices. The analytical contact-force models proposed in the literature are briefly recalled, and a modified version of the classical linear viscoelastic model is introduced. This model is applied tative case study, where the two potentially colliding R/C structures have the same height, but whose response is affected by considerable torsional pounding effects. Based on the results of the pounding assessment analysis, a damped interconnection mitigation solution is suggested by illustrathe retrofit intervention and some of its technical installation details. Two conceptual models have been developed to simulate structural pounding, i.e. the stereo-mechanical approach and the contact element approach, respectively. The former refers to the traditional theory of impact for particles [7], and is based on the principles of conservation of energy and momentum. Impact is evaluated by the coefficient of restitution , which accounts for the energy dissipation related to the plastic effects occurring during the collision, defined as follows: 21vvvv are the approaching velocities, and the post-impact (rebound) velocities. The stereo-mechanical theory is not appropriate for developing a time-history analysis of multi-degree-of freedom structural systems, as it does not simulate the structural response during contact, by assuming a negligible duration of it. In fact, this is an essential phase for the computation of pounding forces, as well as for the influence exerted on the global response of the colliding structures, especially in the frequent case of multiple simultaneous contacts. Moreover, the stereo-mechanical contact model cannot be directly implemented in commercial finite element calculus programs. Therefore, application of this approach is generally confined to research studies focused on the impact of simple bodies, which can be schematized as single-degree-of-freedom systems, and analyzed by specifically developed software. The contact element approach offers a straightforward idealization of the pounding problem, as it corresponds to the intuitive interpretation of the phenomenon. Impact is simulated by a contact element separation gap between the structures shrinks, which allows solving the problem within the framework of an ordinary response analysis. The contact element is obtained by combining in parallel a spring and a viscous damper. The stiffness of the spring is typically assumed to be equal to the axial stiffness of the contacting floor diaphragms (or the stiffness of specific floor portions or members, in case of localized impacts). The spring is generally assumed to be linear elastic or non-linear elastic. In the latter case, reference is commonly made [5], [8] to the Hertz model, which expresses the contact tive displacement between the colliding members, with the exponent fixed at 3/2. Although the non-linear model corresponds to the physical expectation that the contact area will increase as the contact force grows, extensive computational studies [8] have shown that the displacement response of the colliding systems is , and thus that similar numerical results are obtained as compared to the linear model too. The damper element is associated to the elastic spring, either of linear or non-linear tyenergy dissipation occurring during impact. If an elastic spring and a linear viscous dashpot are jointly assumed, the model coincides with the classical linear viscoelastic Kelvin-Voight rheological scheme (upper image in Fig. 1, are the masses of the colliding structures, and is the separation distance at rest). The damping coefficient of the linear dissipater, , can be related to the coefficient of restitution by equating the energy losses during impact [9], obtaining the following expressions: 2121mmmmkc )(lnŠ=is the impact damping ratio, m function. This formulation acceptably agrees with the results of tests on simple impacting systems, except for the fact that the dashpot element is active not only in the approaching phase, but also in the separation time interval. As a consequence, it counters the relative bounce motion pulling ththe early separation motion, which is the opposite of the real physical pounding. In order to bypass this incongruence, a gap element can be with the damper [5], [10], so that the latter is activated only at the approaching stage. This varied scheme, also called Impact Kelvin model, solves the drawback of the original Kelvin-Voight model in terms of numerical response, but not from a conceptual viewpoint. Fig. 1. Rheological schemes of Kelvin-Voight linear elastic and Jankowski non-linear elastic impact models. A gap element placed in series with the damper ( in the lower image in Fig. 1) is included also in the non-linear viscoelastic model proposed by Jankowski [5], where the spring is assumed to be non-linear and responding to the =3/2, and the damping coefficient is transformed into a non-linear function of the time-varying interpenetration depth of the deformed colliding structures, ). The damper impact force is kept as a linear function of the interpenetration velocity )(The expressions of non-linear damping coefficient Jankowski impact damping ratio 2121)(2)(mmmmtktc 16]16)-9([59rr is the stiffness of the Hertzian impact spring (which has the dimensions of a force divided by a 3/2-power law of displacement). In the rheological scheme of Jankowski model, the elastic spring with stiffness introduced in parallel with the damper is aimed at driving the latter to its pre-impact position before a new contact occurs. The analytical model expressed by (4) and (5) is an extension of the Kelvin-Voight model defined by (2) and (3), without the physical incongruence observed for the latter at the rebound phase, thanks to the presence of the . Furthermore, it provides a more careful description of the energy dissipation mechanism involved in pounding, due to the spring and damper being non-linear. However, as the spring and damper reaction forces don’t simultaneously, the impact force–time curve does not vary smoothly when passing from the approach phase to the rebound one. This discontinuity does not correspond to the physical expectations about the time-evolution of the collision force. Moreover, the on time makes the numerical time-history analysis more burdensome. Other more elaborated impact models have been proposed in literature, among which a non-linear viscoelastic scheme incorporating a Hertzian damper (also named Hertz-damp model) [8]. This scheme, extrapolated from different engineering research areas, such as robotics and multi-body systems, has been later modified to overcome an incongruence in the impact damping ratio estimate [10]. Due to their accentuated demodels are affected by notable uncertainties in the calibration of relevant characteristic parameters, and require a great computational effort. Therefore, as long as experimental research cannot demonstrate thmost complex non-linear models and at the same time cannot allow their better parameter tuning, the simplest linear viscoelastic Kelvin-Voight–like assembly can be still suggested for use in the time-history analysis of pounding Anyway, specific modifications capable of removing the pulling (tensile) damping force at the rebound phase, not based on the mere numerical artifice represented by the incorporation of an in series gap element, as discussed above, are required to improve the conceptual basis of the linear viscoelastic model. The study summarized in this paper is carried out within this research framework. The modification introduced as compared to the classical analytical elaboration of the model presented in [9], consists in a different hypothesis about the instant of separation between the colliding structures. In [9] the instant coincides with the condition: ) are the displacemenmembers. This condition does not consider that the contacting surfaces get deformed during impact, and thus separation is anticipated. Here, instead, separation is assumed to occur when the imlled, i.e. when the ()()0)()()()(1l1l=Š+ŠtvtvctutukIn this hypothesis, named: 2121mmmm mkl2=, Š=, the relation between results to be as follows: Š=21122112arctgsinIn order to obtain the dual form typical of (3) and (5), where the damping ratio is expressed as a function of the vice versa), as (7) cannot be inverted to analytically derive this form, an approximated cl k l sep-gap m 2 m 1 cn l k h k d sep-gap d-gap m 1 m 2 relation can be determined by numerical interpolation of this equation. The best fitting relation is 85.0Š=Relations (3), (7) and (8) are plotted in Fig. 2, which shows a satisfactory correlation between the analytical and interpolated expressions of the modified Kelvin-Voight model proposed in this section. Remarkable differences with the original model [9] are noticed in the [0-0.5] where the curves of the modified model approach infinity as tends to zero (theoretical condition of perfectly plastic impact). This trend is consistent with the physical interpretation of impact, and also characterizes relation (5) of the non-linear viscoelastic Jankowski model. The three relations provide nearly coincident values in the [0.8-1] sub-range, and rather similar values in the [0.6-0.8] range, which includes the value of the damping ratio most commonly adopted, i.e. 0.65, which represents the basic choice also in the case study ansection. Fig. 2. relations (3) and (8), and relation (7). The modified Kelvin-Voight model removes the pulling effect of the original model and, unlike Jankowski scheme, provides a smooth (continuous) impact force-time response The case study examined herein is represented by two adjacent six story R/C frame buFriuli region – Italy, designed and built in the early 1960s (Fig. 3). The town of Pordenone lies in a medium seismicity area, characterized by the following site-peak ground new Italian Seismic Standards [11] for the four assumed reference design earthquake levels (frequent—FDE, with 81% probaprobability; basic—BDE, with 10%/50-year probability; and collapse prevention—CPE, with 5%/50-year probability), and B-type soil conditions (deposits of very thick sand, gravel, or very stiff clay, several dozens of meters thick): =0.065 g; =0.236 g; and The two buildings have the same interstory heights, and the same overall structural height (with a small difference in at the roof level of the right building in Fig. 3). The left building includes a penthouse on the top floor, which covers about half of the surface in plancovered by a light metal and glass structure. The main skeleton frames are parallel to the longitudinal direction in plan , which also constitutes the pounding direction. The separation gap along the height is equal to 20 mm, determined by the thickness of the wooden planks making up the formwork of the columns of the right building, which was built two years later than the left building. This is a recurrent configuration for a large stock of of reference Seismic Standards. Fig. 3. General views of the main faÃ§ades of the buildings, and detailed view of the joint zone on top of the ground floor. The finite element model of thcontact elements assembled according with the linear viscoelastic impact rheological scheme discussed in the previous section, characterized by the relation expressed by (7), is displayed in Fig. 4. The model was generated with the SAP2000 commercial calculus program [12], which allows computing dynamic response by a Fast Non-linear Analysis approach that is an alternative solution to the traditional step-by-step time integration approach, with remarkable savings in processing delays. At an early stage of the assessment enquiry, the modal was carried out separately. Rather similar modal characteristics emerged, highlighted by a purely torsional first vibration mode, with period equal to 1.98 s and effective modal mass equal to 18% of the total seismic mass, for the left building, and to 1.79 s and 25%, for the right one. The second and third modes are mainly translational along the axes in plan, respectively. Relevant periods and masses are as follows: 1.47 s and 72% ), 1.16 s and 63% (), for the left building; 1.6 s and 49% Consistently with these modal characteristics, the response history analyses carried out with sets of seven artificial 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2 Coefficient of restitution Relation (3) Relation (7) Relation (8) Impact damping ratio accelerograms generated from the pseudo-acceleration response spectra referred to the four normative earthquake levels mentioned above, highlighted torsion-dominated pounding effects. The highest demand was computed in both structures along the perimeter frame of the main faÃ§ade, which is opposite the C-shaped R/C wall enclosing the Fig. 4. Finite element model of the two structures, including linear viscoelastic impact elements governed by (7) across the separation gap. As way of example of the results of the dynamic analyses, the impact force time-history of the faÃ§ade frames obtained from the most demanding input motion scaled at the CPE level intensity, is plotted in Fig. 5. Fig. 5. Impact force time-history of the faÃ§ade frames obtained from the most demanding input motion scaled at CPE level intensity. Peak forces were found to be greater than 10,000 kN, and the other two colliding frame alignments. This causes unsafe conditions for 53 columns (out of 139 in total) for the left building, and 77 columns (out of 154), for the right one. Severe damage is also noticed for most beams and the R/C shaped walls. Two types of FV dissipaters were adopted in the mitigation hypothesis formulated for this case study. The first type is represented by spring-dampers made of an internal cylindrical casing filled with a compressible silicone fluid pressurized by a static pre-load applied upon manufacturing; of a piston moving in this fluid; and of an external casing (Fig. 6). The operating mechanism is based on the silicone fluid piston head and the internal casing [13]-[15]. The inherent re-centering capacity of the device is ensured by the initial pressurization of the fluid [13], [16]. The total dynamic reaction force exerted by the device is the sum of ) damping and ) non-linear elastic reaction forces corresponding to their damper and spring functions, respectively. ) can be expressed analytically as follows [17], [13]: Fig. 6. Cross section of a pressurized FV spring-damper. )())(sgn()(txtxctF txktxkktxktF/121)()()()()(+==damping coefficient; sgn(Â·)=signum function; |Â·|=absolute value; =fractional exponent, ranging from 0.1 to 0.2; =static pressurization pre-load; the response branches situated below and beyond ; and =integer exponent, set as equal to 5 [13], [18]-[20]. The finite element model of FV spring-dampers is obtained by combining in parallel a non-linear dashpot element and a non-linear spring element with reaction forces given by (9) and (10), respectively. Both types of elements are currently incorporated in commercial structural analysis programs, like the SAP2000 code used in this study [12]. In this assembly, the static pre-load is imposed as an internal force to a bar linking the two elements. In order to simulate the attainment of the spring-damper strokes, the device model can be completed by adding a “gap” element and a “hook” element, aimed at disconnecting the device when stressed in tension, and at stopping it when the maximum displacement in compression is reached, respectively [21]-[24].The second type of FV device is a simple damper, without the spring function. In this case, the piston crosses the external casing on both sides. The response of the damper is described by (10) too, and its finite element model is obtained by the same assembly as described above, but not including the spring component. The basic objective of the mitigation hypothesis formulated in this section was to prevent collisions up to the CPE level of seismic action. The design solution consisted in incorporating four FV spring-dampers and seven FV pure dampers. The former were placed across the two perimeter frames on the second and third stories, so as to produce a small increase in the separation gap at rest (about 10 mm). This allows extending the available free displacement at the approaching phase, and thus the response cycles of the devices and their dissipative action. The spring function was not required on the upper stories, where the seven pure dampers were put across the perimeter frames too (fourth and Interfacing plate Internal casing External casing Piston Stop-block Silicone fluid Connection flange Seal x y 0 5 1 0 1 5 2 0 2 5 Time (s) fifth stories), on botand on the central frame (sixth). The positions of the eleven devices are highlighted with rhomboidal (spring-dampers) and triangular (pure dampers) arrows in Fig. 7, where an elevation view of the structural model and of the fifth story plan are drawn. The maximum energy dissipation capacity and stroke of the selected devices are as follows [25]: 50 kJ and 120 mm—spring-dampers; 57 kJ and 100 mm—pure dampers. Fig. 7. Positions of the FV devices in elevation and on the fifth story plan. Renderings of the installation of two FV spring-dampers on the faÃ§ade, before and after their covering with metallic carters, and of one of the two pure dampers situated on the Fig. 8. Renderings of the installation of some FV devices. The envelope of the maximum relative displacements between the two structures obtained from the most demanding CPE-scaled input motion is plotted in Fig. 9. Thanks to the protective action guaranteed by the FV devices, the displacements are constrained below 20 mm up to the sixth story. This allows meeting the targeted no-collision objective, also without considering the increase in gap depth produced by the spring-dampers located on the third and fourth stories. Fig. 9. Envelope of the maximum relative displacements between the two structures obtained from the most demanding CPE-scaled input motion. The number of columns in nominally unsafe conditions is reduced to only 2 and 5 for the left and right building, respectively. This is a consequence of the retrofit intervention, which not only prevents the structures from pounding, but also remarkably reduces their response as compared to the theoretical would be enough to accommodate their free relative oscillations. Indeed, in this case the unsafe columns would be 29 (left) and 43 (right). Similar improvements are also noticed for the beams aThe analysis of seismic pounding represents one of the most topical research fields in earthquake engineering. Experimental studies are still required, especially on es, to definitely validate the analytical models used to simulate impact between colliding buildings. Theoretical improvements of these models, as well as updated criteria for their numerical implementation, should also be developed further. Concerning pounding mitigation,protective, limitedly invasive and relatively low-cost solutions can nowadays be obtained by incorporating passive energy dissipaters. The most proper choice of the damping timal sizing and installation ng topics for researchers and designers. The study summarized in this paper was aimed at offering some contributions both from an analytical modeling and a technical mitigation viewpoints. The modified version of the linear viscoelastic model obtained by equating the contact forces of the colliding structures at the instant of impact, rather than their displacementspulling rebound force. At the same time, unlike the non-linear viscoelastic Jankowski rheological scheme, the updated linear model provides a smooth impact force–time response curve over the approach and rebound collision The interconnection-based solution devised for pounding mitigation, based on the incorporation of fluid viscous dissipaters across the separation gaps, offered positive indications in the case study examined here. This was assessed by achieving the highly demanding performance objective of no collisions for the seismic action scaled up to the intensity of the collapse prevention earthquake level, starting from a minimal at-rest depth of the existing gap between the two considered buildings. Furthermore, it was observed that, in addition to the effective pounding prevention obtained, the incorporation of FV devices remarkably reduced the response of the buildings as compared to their theoretically independent (non-pounding) response. Based on this observation, the mitigation intervention proposed in this study can be viewed as a global seismic retrofit strafeaturing inadequate separation gaps. on gaps. S. A. Anagnostopoulos, “Building pounding re-examined: How serious a problem is it?” in Proc. 10 European Conference on Earthquake Engineering, 1996, pp. 2108. G. L. Cole, R. P. Dhakal, A. J. Carr, and D. K. Bull, “Building pounding state of the art: Identifying structures vulnerable to pounding -20 -17.5 -15 -12.5 -10 -7.5 -5 -2.5 0 1 2 3 4 5 6 Displacement (mm)Story damage,” in Proc. 2010 New Zealand Society for Earthquake Engineering Conference, 2010, pp. 11. B. D. Westermo, “The dynamics of interstructural connection to prevent pounding,” Earthquake Engineering and Structural Dynamicsvol. 18, no. 6, pp. 687-699, June 1989. V. Varnotte, “Mitigation of pounding between adjacent buildings in earthquake situation,” Ph.D. Thesis, University of Liege, 2008. R. Jankowski, “Modelling of eartEarthquake Engineering and Structural Dynamics, vol. 34, no. 6, pp. 595-611, June 2005. R. Jankowski, K. Wilde, and Y. Fujino, “Pounding of superstructure segments in isolated elevated bridge during earthquakes,” Earthquake Engineering and Structural Dynamics, vol. 27, no. 5, pp. 487-502, May 1998. W. Goldsmith, Impact: The Theory and Physical Behaviour of , London: Edward Arnold, 1960. S. Muthukumar and R. DesRoches, “A Hertz contact model with nonlinear damping for pounding simulation,” Earthquake Engineering , vol. 35, no. 7, pp. 811-828, July 2006. S. A. Anagnostopoulos, “Pounding of buildings in series during earthquakes,” Earthquake Engineering & Structural Dynamics, vol.16, no. 3, pp. 443-456, March 1988. Y. Kum, L. Li, and Z. Hongping, “A modified Kelvin impact model for pounding simulation of base-isolaEarthquake Engineering and Engineering Vibration, vol. 8, no. 3, pp. 433-446, Sep. 2009. Italian Council of Public Works, [in Italian], Ministry of Public Works, G.U. February 4Rome, Italy, 2008. Computers and Structures Inc., SAP2000. Structural Analysis Programs-Theoretical and Users Manual, Release No. 14.09. Berkeley, CA: CSI, 2012. S. Sorace and G. Terenzi, “Non-linear dynamic modelling and design procedure of FV spring-dampers for base isolation,” Engineering , vol. 23, no. 12, pp. 1556-1567, Dec. 2001. S. Sorace and G. Terenzi, “Non-linear dynamic design procedure of FV spring-dampers for base isolation — Frame building applications,” Engineering Structures, vol. 23, no. 12, pp. 1568-1576, Dec. 2001. F. J. Molina, S. Sorace, G. Terenzi, G. Magonette, and B. Viaccoz, “Seismic tests on reinforced concrete and steel frames retrofitted with Earthquake Engineering and Structural Dynamicsvol. 33, no. 12, pp. 1373-1394, Nov. 2004. S. Sorace, G. Terenzi, G. Magonette, and F. J. Molina, “Experimental investigation on a base isolation system incorporating steel-Teflon sliders and pressurized fluid viscous spring dampers,” Earthquake Engineering and Structural Dynamics, vol. 34, no. 2, pp. 225-242, Feb. 2008. G. Pekcan, J. B. Mander, and S. S. Chen, “The Seismic response of a 1:3 scale model R.C. structure with elastomeric spring dampers,” Earthquake Spectra, vol. 11, no. 2, pp. 249-267, May 1995. S. Sorace and G. Terenzi, “Analysis and demonstrative application of a base isolation/supplemental damping technology,” Earthquake Spectravol. 24, no. 3, pp. 775-793, Aug. 2008. S. Sorace and G. Terenzi, “The damped cable system for seismic protection of frame structures — Part I: General concepts, testing and modelling,” Earthquake Engineering and Structural Dynamics, vol. 41, no. 5, pp. 915-928, Apr. 2012. S. Sorace and G. Terenzi, “The damped cable system for seismic protection of frame structures — Part II: design and application,” Earthquake Engineering and Structural Dynamics, vol. 41, no. 5, pp. 929-947, Apr. 2012. S. Sorace and G. Terenzi, “Seismic protection of Frame structures by fluid viscous damped braces,” Journal of Structural EngineeringASCE, vol. 134, no. 1, pp. 45-55, Jan. 2008. S. Sorace and G. Terenzi, “Fluid viscous damped-based seismic retrofit strategies of steel structures: General concepts and design applications,” Advanced Steel Construction, vol. 5, no. 3, pp. 322-339, Sep. 2009. S. Sorace, G. Terenzi, and G. Bertino, “Viscous dissipative, ductility-based and elastic bracing design solutions for an indoor sports steel building,” Advanced Steel Construction, vol. 8, no. 3, pp. 295-316, Sep. 2012. S. Sorace and G. Terenzi, “Shaking table and numerical seismic performance evaluation of a fluid issipative bracing system,” Earthquake Spectra, vol. 28, no. 4, Nov. 2012. S. L. Jarret. Shock-control Technologies. URL. [Online]. Available: was graduated "cum laude" in Civil Engineering - Structural SecFlorence, in 1985. In 1990 Structural Engineering at the University of Florence, and from 1991 to 1998 he was a researcher at the Faculty of Engineering of the University of Perugia. Since 1998 he is associate professor of Structural of Udine. He is author of more than 130 scientific papers, several of which printed in international journals. Two among these papers were jointly awarded the 2001 edition of the "Munro PrEngineering Structures journal, Elsevier Ltd. Another paper was awarded the 2002 "IABSE Outstanding Paper award", for the best paper Structural Engineering International journal. His research fields concern various topics within earthquake engineering, advanced seismic protection of structures, structural modelling and assessment, structural rehabilitation, the time-dependent behaviour of building materials, and the dynamic characterisation of structural members and systems. He was the Scientific Responsible person for the University of Udine in several International EC Funded Research Projects, among which “SPIDER" (Strand Pre-stressing for Internal Damping of Earthquake Response), "CASCADE" (Co-operation And Standardisation in the Control of Advanced Dynamic Experiments), and "DISPASS" (Dissipation and Isolation Passive Systems Study), for which he was also the general Coordinator; and Italian National Research Projects, among which PRIN 1999, PRIN 2008, Reluis-DPC 2005-2008, and Reluis-DPC 2010-2013.Gloria Terenzi was graduated "cum laude" in Civil Engineering - Structural SecRome "La Sapienza", in 1991. In 1996 she received her PhD in Structural Engineering at the University of Florence. Since 2001 she is a researcher at the Faculty of Engineering of the University of Florence. At the same University, since 2002 she is teaching Structural Engineering II, and since 2003 she is also teaching Earthquake Engineering. She is author of about 100 scientific papers, several of which pramong these papers were jointly awPrize", for the best paper published every year in Engineering Structuresjournal, Elsevier Ltd. Another paper was awarded the 2002 "IABSE Outstanding Paper award", for the best paper published every year in Structural Engineering International journal. Her research fields concern various topics within earthquake engineering, advanced seismic protection of structures, performance analysis of historical buildings, assessment of structural elements with fiber-reinforced composite materials, and performance evaluation of new and existing reinforced concrete structures. She was and is currently taking part to Teams working in International EC-funded Research Projects, among which “SPIDER" (Strand Pre-stressing for Internal Damping of Earthquake Response), "CASCADE" (Co-operation And Standardisation in the Control of Advanced Dynamic Experiments), and "DISPASS" (Dissipation and Isolation Passive Systems Study); and Italian National Research Projects, among which MURST 1995-1997, PRIN 1997, PRIN 1999, PRIN 2008, Reluis-DPC 2005-2008, and Reluis-DPC 2010-2013.

Please download the presentation from below link :

Download Pdf - The PPT/PDF document "Abstract" is the property of its rightful owner. Permission is granted to download and print the materials on this web site for personal, non-commercial use only, and to display it on your personal computer provided you do not modify the materials and that you retain all copyright notices contained in the materials. By downloading content from our website, you accept the terms of this agreement.

Try DocSlides online tool for compressing your PDF Files Try Now

pdf-slides
2 views

pptx
11 views

pptx
47 views

pptx
34 views

pptx
42 views

pptx
79 views

pptx
47 views

pptx
73 views

pptx
63 views